Primo PS-10 10" Meat Slicer

Model #PS-10 By Primo
$495.00
Save $495.00
$990.00

Free Shipping!

Ships in 24 - 48 Hours From 1 of

3 Locations? Plattsburgh, NY (12901)
Dallas, TX (75001)
Compton, Ca (90059)

The Primo PS-10 10” Meat Slicer

The new Primo semiautomatic slicer is an improved table styled meat slicer. Its design provides sufficient pressure on the meat, resulting with better thickness control and cleaner slices. These improvements allow for ease of operation. Operators will be able to easily slide the deck support. Cleaning and maintaining the slicer is also easier, allowing for quicker product changes.

  • Reliable and dependable belt drive design
  • Removable carriage for easy maintenance
  • Adjustable slicing knob
  • Built-in sharpener
  • Ring guard
  • Permanent lubricated carriage ball bearings to ensure quiet operation
  • .25 HP

Operation

  • Place the machine on a flat stable work surface. Plug the power cord into a 120V outlet.
  • Raise up the meat pressing board and put the meat onto the meat deck, and press the green button.
  • Adjust the slicing thickness according to your need. Push and pull the Deck support by the handle.

Slicing

Before the machine is used, the gliding systems and the pressing pole should be cleaned and well lubricated. This will allow for smooth movements of the carriage and pusher.

When slicing a wide variety of meats, best results are achieved when the meat is unfrozen. Recommended temperatures for meat products are 4C or 40F. In some cases, frozen meats can be sliced, but the temperature range should remain between -5C and 4C for best results.

Raise the Meat pressure Plate and place the meat onto the Meat Support Deck. Start the machine by pressing the Green Power button located on the side of the machine. Adjust the slice thickness by turning the Thickness Adjustment knob located on the side of the machine. You have a good range of thicknesses to meet your customers' requirements

The meat is sliced by sliding the meat Deck past the cutting blade. You pull the Meat Deck back to repeat the process. Continue until you have completed the order. Upon completion, move the meat Deck back off of the blade before removing the meat from the slicer.

Blade Sharpening

The blade should be sharpened frequently to achieve best results.

Clean the blade thoroughly to remove all debris. This debris can accumulate in the sharpening stone, reducing the sharpening capacity. The stone should be cleaned after each sharpening to again remove any debris caught on the stone.

Note: Ensure the unit is off before starting the blade sharpening operation. Do not rush through this operation. Care should be taken to avoid injury from the rotating components.

Step 1- Loosen the knob that secures the sharpening stones

Step 2-Pull up on the stone assembly and rotate the assembly 180 degrees so that the stones come in contact with the blade.

Step 3- Tighten the knob to secure the stone assembly in place.

Step 4- Press the green power button located on the side of the slicer. Ensure the blade is turning

Step 5- Locate the stone support pins located on the outside of the stone assembly. One is for the front and one is for the back of the blade. Place your hand on the top of the stone assembly guard and with your thumb push onto the pin located on the side of the assembly so that the stone contacts the blade. Hold this for 20-40 seconds. Repeat for the other stone – making sure you use your thumb to push the pin. This is to prevent your fingers from potential injury due to the rotating blade.

Step 6- Turn the power off and once the blade has stopped turning, wipe the blade to remove any debris.

Step 7- Loosen the knob on the stone assembly, lift up and rotate 180 degrees into its stored position. Tighten knob to secure the assembly in place.

Maintenance and Cleaning

All moving parts both static and automatic should be properly lubricated to maintain years of smooth operation of your slicer. Mineral oil must be used to lubricate the sliding parts.

Inspect all safety guards, the condition of the power cord and the overall condition of all the components of your slicer for cleanliness and integrity (no frayed ends or burrs). Visually inspect the blade. Insure there are no nicks or cracks nor debris.

Power on the slicer and inspect for smooth rotation of the blade. If you hear any abnormal noises, stop the slicer, unplug the unit and have a qualified service technician fix any issues. Continued use of the slicer, if abnormal noises are present could damage the unit and void your warranty. Noises such as rubbing, grinding or excessive vibration are a concern. An ozone or burnt smell could indicate an electrical problem. Unplug the unit immediately if you smell burning or ozone.

If service is required for your slicer, unplug the unit from the wall before dismantling the unit. Failure to do so could result in an electric shock to the service technician.

When cleaning the unit, use warm soapy water, not harsh chemicals and never use a pressure washer. Care must be taken when cleaning near or around the blade. The use of safety gloves is recommended.

Use the online HTML, CSS, JavaScript tool collection to make websites easily.

  • Compact, and fashionable space saving design
  • Easy to operate
  • Anodized aluminum housing resists corrosion
  • Tilted 10” blade made of hardened stainless steel
  • Adjustable cutting thickness up to 0.47” (12 mm)
  • Carriage ball bearings for smooth operation
  • Built-in sharpener
  • Tray mounted safety guard
  • Quick and easy to disassemble for cleaning
  • No volt safety release
  • Blade guard safety switch
  • Blade ring guard for safety while cleaning
  • Air-cooled motor with overload protection
  • Reliable and dependable belt drive design
  • Water & dust proof switch with power indicator light
  • Note: Not recommended for slicing cheese

Warranty:

One year parts & Labor (Carry-in). Note: Specifications subject to change without notice.

Specifications
Equipment Type Presto Slicers
Brand Primo
Model PS-10
Electrical 120V/60Hz/1Ph
HP 0.25
RPM 300
Blade Diameter 10”
Slice Thickness 0-12 mm
Dimensions
Width 21"
Height 23"
Depth 19"
Shipping Weight 35 lbs.
Intertek ETL Listed US & Canada Intertek ETL Listed US & Canada

The ETL Mark is proof of product compliance to North American and Canadian safety standards. Authorities Having Jurisdiction(AHJs) and code officials across the US and Canada accept the ETL Listed Mark as proof of product compliance to published industry standards. Retail buyers accept it on products they're sourcing. And every day, more and more consumers recognize it on products they purchase as a symbol of safety.

ETL Sanitation Listed Intertek ETL Sanitation Listed

The ETL Sanitation Mark indicates that the manufacturer's production site conforms to a range of compliance measures and is subject to a periodic regimen of follow-up inspections to verify continued conformance. An ETL Sanitation Mark on Food Service Equipment indicates that equipment is fit for use in the production of food intended for human consumption, or the equipment is fit for use in an environment where food intended for human consumption is produced.

Plug Type: NEMA 5-15P Plug Type: NEMA 5-15P

The plug type for this product is NEMA 5-15P.

We pride ourselves for...

Our technical support expertise

Our team is trained to help you from the moment you receive your delivery. Whether it's assembly, installation, or general technical support, our specialists are here to make sure you get the most out of your product. We offer technical support to all of our customers. Please try to have your order number ready when you call.

Our friendly customer service

When you call us or email us, there is always someone on the other end with a smile on their face; ready to help you with whatever you need. You can call us for anything like general questions about placing an order to specific questions about product features and details, or even if you need us to help you put in a warranty claim; we're here to help.

Being fulfillment professionals

We understand how important it is for you to get your order delivered on time. Therefore, we use some of the best tools and systems to make sure your order process goes smooth and your products arrive on time. We know that time is one of the most valuable assets a business has and we don't take that lightly.

Making our customers happy!

It feels good knowing that we make our customers happy. So how do we do it? Simple. Our goal is to provide a service as opposed to just selling a product. We want to make sure that you have all of the support that you need from before you place your order and for the duration of the time you use your products. Not only that, but we aim to become your back end support system for all of your equipment and supplies needs. We're here for you.

 

You recently viewed

Clear recently viewed
}